The Flying Eagle
Armorer Maintenance Manual • 4.0" & 4.25" 9mm

S&W M&P9 M2.0 (4.0" Compact & 4.25" Full): Field Strip, Cleaning & Reassembly Guide

A clear, step-by-step visual guide for unloading, field stripping, cleaning, lubricating, and function-checking both the 4.0" Compact and 4.25" Full-Size Smith & Wesson M&P9 M2.0 pistols.

Smith and Wesson M&P9 M2.0 4.0-inch Compact and 4.25-inch Full pistol on an armory bench
SAFE UNLOAD • TAKEDOWN • BORE & RAIL CARE • FUNCTION CHECK

Recommended Cleaning Supplies & Bench Setup

Both the 4.0" Compact and 4.25" Full-Size S&W M&P9 M2.0 field strip with zero tools. Clear all live ammunition from your work area and gather basic maintenance supplies before starting:

Supply Item Purpose on the S&W M&P9 M2.0 (4.0" & 4.25") Where to View
9mm Bore Brush, Patches & Cleaning Rod / Bore Snake Cleans fouling from the 4.0" or 4.25" 1:10 twist barrel bore Gear Storefront →
Firearm Cleaning Solvent / CLP Breaks down powder residue on the breech face, feed ramp, and steel chassis rails Gear Storefront →
Nylon Utility Brush, Swabs & Lint-Free Cloths Scrubs carbon around the extractor, sear area, and slide channels Gear Storefront →
Synthetic Gun Oil Provides a light lubricating film on the chassis rails and barrel exterior Gear Storefront →

Part 1: Unloading & Safety Verification

Always treat the firearm as loaded until you have personally confirmed that both the magazine well and chamber are empty:

  1. Point in a Safe Direction: Keep the muzzle pointed in a safe direction and keep your finger off the trigger and outside the trigger guard.
  2. Remove the Magazine: Press the magazine release button and pull the magazine completely out of the grip.
  3. Lock the Slide to the Rear: Pull the slide fully to the rear and push the slide stop lever upward into the slide notch.
  4. Visually and Physically Inspect: Look into the ejection port and magazine well, and insert a finger into the chamber area to confirm no cartridge is present.
1A. DROP MAGAZINE EJECT 1B. LOCK SLIDE TO REAR PUSH SLIDE STOP UP 1C. INSPECT CLEAR EMPTY 1. Visually & physically check 2. Verify empty mag well
Step 1 Safety Check: Remove the magazine, lock the slide open with the slide stop lever, and visually and physically verify an empty chamber and magazine well.

Part 2: Field Stripping the S&W M&P9 M2.0 (4.0" & 4.25")

The M&P M2.0 uses a downward-rotating takedown lever and an internal sear deactivation lever so you do not have to pull the trigger to release the slide:

  1. Rotate the Takedown Lever Downward: With the slide locked to the rear, rotate the takedown lever downward (toward the 6 o'clock position).
  2. Release the Slide & Lower the Sear Deactivation Lever: Pull the slide back slightly and release it to battery, then use a non-marring tool or punch to push the sear deactivation lever down inside the rear of the frame/ejection area while easing the slide slightly forward to clear the sear.
  3. Slide the Upper Forward Off the Frame: Guide the slide assembly smoothly forward off the front of the frame rails.
  4. Remove the Recoil Spring Assembly & Barrel: Turn the slide upside down, compress/lift the recoil spring assembly slightly to unseat it from the barrel lug and lift it out, then lift the rear of the 4.0" or 4.25" barrel upward and slide it out.
2A. ROTATE LEVER DOWN & DROP SEAR Rotate takedown lever down & depress sear deactivation lever 2B. SLIDE UPPER FORWARD OFF FRAME Ease slide forward off chassis rails
Step 2 Takedown: Rotate the takedown lever downward with the slide locked back, release the slide and depress the sear deactivation lever, then ease the slide forward off the frame.
FIELD-STRIPPED S&W M&P9 M2.0 (4.0" & 4.25" ASSEMBLIES) 1. M2.0 Slide Assembly Keep striker channel dry 2. 4.0" or 4.25" Barrel Bore, chamber & feed ramp 3. Recoil Spring Captured spring & guide rod 4. Polymer Frame Steel chassis rails & sear
Four Field-Stripped Groups: Your S&W M&P9 M2.0 (4.0" Compact or 4.25" Full) is separated into the Slide, Barrel, Recoil Spring Assembly, and Polymer Frame.

Part 3: Cleaning & Lubrication

Clean powder fouling from each assembly, wipe dry, and apply light lubrication only to designated friction points:

M&P9 M2.0 LUBRICATION MAP (LIGHT OIL — KEEP STRIKER DRY) BARREL & SLIDE POINTS Thin oil film on barrel hood, lugs & exterior Keep bore, breech face & striker channel DRY CHASSIS RAILS & SEAR (5 DROPS) 1 small drop on each of the 4 chassis rail pads + light oil at sear / trigger bar contact
Step 4 Lubrication Map: Apply a thin sheen of oil to the barrel hood and exterior plus light oil on the 4 chassis rail pads and sear contact while keeping the striker and bore dry.

Part 4: Reassembly & Function Check

  1. Reinstall the Barrel & Recoil Assembly: Drop the barrel into the inverted slide, then seat the recoil spring assembly into the front slide opening and compress it squarely onto the barrel lug seat.
  2. Fit the Slide onto the Frame: Align the slide rails with the frame chassis rails and pull the slide all the way to the rear, locking it open with the slide stop lever.
  3. Return the Takedown Lever: Rotate the takedown lever back up/forward to its normal locked position, then release the slide forward.
  4. Perform a Dry Function Check (Confirm Unloaded First): Rack the slide 2–3 times to verify smooth cycling, check trigger press and tactile reset, and test that the slide locks open on an empty magazine.
5A. SEAT BARREL & SPRING 1. Drop barrel into slide 2. Seat recoil spring assembly firmly on barrel lug seat 5B. INSTALL SLIDE & LEVER Rack slide back & return takedown lever to locked position 5C. DRY FUNCTION CHECK 1. Rack slide 2–3 times 2. Verify trigger break & reset 3. Test empty-mag slide lock
Step 5 Reassembly & Verification: Seat the barrel and recoil spring, fit the slide onto the frame rails, return the takedown lever to its locked position, and complete a dry function check.

Best Maintenance Habits

  • Confirm an empty chamber and magazine well before every step
  • Keep the striker channel, breech face, and bore dry after cleaning
  • Use light oil on the 4 chassis rail pads and barrel exterior
  • Complete a dry trigger, reset, and empty-magazine slide-lock check

Common Mistakes to Avoid

  • Spraying cleaner or oil directly into the striker channel
  • Over-oiling chassis rails or grip surfaces so dust and lint stick
  • Seating the recoil spring improperly against the barrel lug
  • Forgetting to return the takedown lever to its locked position before firing

Video Walkthrough: Smith & Wesson M&P 9mm Gen 2 Field Strip & Reassembly

Watch a step-by-step field strip, reassembly, and function check walkthrough for the Smith & Wesson M&P 9mm M2.0.