The Flying Eagle
Armorer Maintenance Manual • 3.7" Compact 9mm

Springfield Hellcat Pro / Pro Comp (3.7"): Field Strip, Cleaning & Reassembly Guide

A clear, step-by-step visual walkthrough for safely unloading, field stripping, cleaning, lubricating, and function-checking your Springfield Armory Hellcat Pro or Pro Comp (3.7") 9mm pistol.

Springfield Hellcat Pro 3.7-inch 9mm pistol with red dot and weapon light
SAFE UNLOAD • TAKEDOWN • 3.7" BORE & COMP CARE • FUNCTION CHECK

Recommended Cleaning Supplies & Bench Setup

The Springfield Hellcat Pro and Pro Comp (3.7") field strip cleanly without specialty tools. Clear all live ammunition from your work bench and gather basic supplies before starting—including extra attention to carbon/lint around the slide serrations, micro red dot cut, and compensated port/muzzle area on Pro Comp models:

Supply Item Purpose on the Springfield Hellcat Pro / Pro Comp (3.7") Where to View
9mm Bore Brush, Patches & Cleaning Rod / Bore Snake Clears fouling from the 3.7" hammer-forged barrel bore from chamber to muzzle Gear Storefront →
Firearm Cleaning Solvent / CLP Loosens carbon on the feed ramp, breech face, rails, and Pro Comp compensator/barrel crown Gear Storefront →
Nylon Utility Brush, Swabs & Lint-Free Cloths Removes carry lint and powder fouling from rails, micro-fissure texture, and OSP optic pocket Gear Storefront →
Synthetic Gun Oil Applies a light oil film to the 4 frame rail tabs, disconnector contact, and barrel hood Gear Storefront →

Part 1: Unloading & Safety Verification

Always treat the pistol as loaded until you have personally confirmed that both the magazine well and chamber are empty:

  1. Point in a Safe Direction: Keep the muzzle pointed in a safe direction and keep your finger completely off the trigger and outside the trigger guard.
  2. Eject the Magazine: Press the magazine release button and pull the 15-round (or extended) magazine completely out of the grip.
  3. Lock the Slide to the Rear: Pull the slide fully to the rear and push the slide stop lever upward into the slide notch.
  4. Visually and Physically Inspect: Look into the ejection port and magazine well, and insert a finger into the chamber area to confirm no round is present.
1A. EJECT MAGAZINE DROP 1B. LOCK SLIDE TO REAR PUSH SLIDE STOP UP 1C. INSPECT CLEAR EMPTY 1. Visually & physically check 2. Verify empty mag well
Step 1 Safety Check: Remove the magazine, lock the slide open with the slide stop lever, and visually and physically verify an empty chamber and magazine well.

Part 2: Field Stripping the Springfield Hellcat Pro / Pro Comp (3.7")

Like the standard 3" Hellcat, the 3.7" Hellcat Pro and Pro Comp use an upward-rotating takedown lever:

  1. Rotate the Takedown Lever Upward: With the slide locked to the rear, rotate the left-side takedown lever upward to the vertical 12 o'clock position.
  2. Ease the Slide Forward: Pull the slide slightly rearward to release tension on the slide stop, then guide the 3.7" slide assembly smoothly forward off the front of the frame.
  3. Remove the Dual Recoil Spring Assembly: Turn the slide upside down, push the captured dual recoil spring assembly slightly forward toward the muzzle to unseat it from the barrel lug, and lift it out without prying the springs apart.
  4. Lift Out the 3.7" Barrel: Lift the rear of the 3.7" barrel upward and slide it out through the bottom/front of the slide.
2A. ROTATE TAKEDOWN LEVER UP (12 O'CLOCK) With slide locked back, rotate takedown lever straight UP 2B. EASE 3.7" SLIDE FORWARD OFF FRAME Release slide stop & guide slide forward off frame
Step 2 Takedown: Rotate the left-side takedown lever upward to 12 o'clock with the slide locked back, then ease the 3.7" upper forward off the frame.
FIELD-STRIPPED SPRINGFIELD HELLCAT PRO / PRO COMP (4 GROUPS) 1. 3.7" Slide / Pro Comp Keep striker channel dry 2. 3.7" Barrel Bore, feed ramp & crown 3. Dual Recoil Spring Captured unit—do not pry 4. Polymer Frame 4 steel rail tabs + sear
Four Field-Stripped Groups: Your Hellcat Pro / Pro Comp (3.7") is separated into the Slide, 3.7" Barrel, Dual Captured Recoil Spring Assembly, and Polymer Frame.

Part 3: Cleaning & Lubrication

Clean fouling and carry lint from each assembly, wipe dry, and apply only a light oil film to designated friction points:

HELLCAT PRO LUBRICATION MAP (LIGHT OIL — DO NOT OVER-OIL) 3.7" BARREL & SLIDE POINTS Thin oil film on barrel hood, lugs & exterior Keep bore, breech face & striker channel DRY FRAME RAILS & CONNECTOR (5 DROPS) 1 small drop on each of the 4 frame rail tabs + 1 drop at trigger bar / disconnector contact
Step 4 Lubrication Map: Apply a thin sheen of oil to the 3.7" barrel hood and exterior plus 1 small drop on each of the 4 frame rail tabs and disconnector contact while keeping the bore and striker dry.

Part 4: Reassembly & Function Check

  1. Reinstall the 3.7" Barrel & Dual Recoil Assembly: Drop the 3.7" barrel into the inverted slide, then insert and compress the captured dual recoil spring assembly so its rear seats squarely on the lower step of the barrel lug.
  2. Fit the Slide onto the Frame: Align the slide channels with the frame rails and pull the slide all the way back, locking it open with the slide stop lever.
  3. Return the Takedown Lever: Rotate the takedown lever counter-clockwise/downward back to its horizontal 9 o'clock position, then release the slide forward.
  4. Perform a Dry Function Check (Confirm Unloaded First): Rack the slide 2–3 times to verify smooth cycling and full return to battery, confirm trigger press and tactile reset, and test that the slide locks open on an empty magazine.
5A. SEAT BARREL & SPRING 1. Drop 3.7" barrel into slide 2. Seat dual recoil spring against lower barrel lug step 5B. INSTALL SLIDE & LEVER Lock slide back & rotate takedown lever DOWN 5C. DRY FUNCTION CHECK 1. Rack slide 2–3 times 2. Verify trigger break & reset 3. Test empty-mag slide lock
Step 5 Reassembly & Verification: Seat the 3.7" barrel and dual recoil spring, fit the slide onto the frame rails, return the takedown lever horizontal, and run a dry function check.

Best Maintenance Habits

  • Verify an empty chamber and magazine well before every step
  • Keep the striker channel, breech face, and bore dry after cleaning
  • Use light oil (4 rail drops + thin barrel film) without over-lubricating
  • Complete a dry trigger, reset, and empty-magazine slide-lock check

Common Mistakes to Avoid

  • Spraying cleaner or oil directly into the striker channel
  • Prying apart the captured dual recoil spring assembly
  • Over-oiling carry surfaces so lint and carbon stick
  • Forgetting to rotate the takedown lever back to horizontal before firing

Video Walkthrough: Springfield Armory Hellcat Pro Tabletop Review and Field Strip

Watch a step-by-step tabletop review and field strip walkthrough for the Springfield Armory Hellcat Pro.