The Flying Eagle
Armorer Maintenance Manual • Gen 5 9mm

Glock 19 Gen 5 / G19 MOS: Field Strip, Cleaning & Reassembly Guide

A clear, step-by-step visual guide for unloading, field stripping, cleaning, lubricating, and function-checking the Glock 19 Gen 5 and G19 MOS 9mm compact pistol.

Glock 19 Gen 5 pistol with slide-mounted red dot sight and weapon light
SAFE UNLOAD • TAKEDOWN • BORE & RAIL CARE • FUNCTION CHECK

Recommended Cleaning Supplies & Bench Setup

Field stripping a Glock 19 Gen 5 or G19 MOS takes less than a minute without specialty tools. Clear all live ammunition from your work area and gather basic maintenance supplies before starting:

Supply Item Purpose on the Glock 19 Gen 5 / G19 MOS Where to View
9mm Bore Brush, Patches & Cleaning Rod / Bore Snake Cleans fouling from the 4.02" Glock Marksman Barrel (GMB) bore Gear Storefront →
Firearm Cleaning Solvent / CLP Breaks down powder residue on the breech face, feed ramp, and slide rails Gear Storefront →
Nylon Utility Brush, Swabs & Lint-Free Cloths Scrubs fouling around the extractor, frame rails, and MOS plate/optic area Gear Storefront →
Synthetic Gun Oil Applies a light oil film to the 4 frame rail pads, connector tab, and barrel hood Gear Storefront →

Part 1: Unloading & Safety Verification

Always treat the firearm as loaded until you have personally confirmed that both the magazine well and chamber are empty:

  1. Point in a Safe Direction: Keep the muzzle pointed in a safe direction and keep your finger off the trigger and outside the trigger guard.
  2. Remove the Magazine: Press the magazine release button and pull the magazine completely out of the grip.
  3. Lock the Slide to the Rear: Pull the slide fully to the rear and push the slide stop lever upward into the slide notch.
  4. Visually and Physically Inspect: Look into the ejection port and magazine well, and insert a finger into the chamber area to confirm no round is present.
1A. DROP MAGAZINE EJECT 1B. LOCK SLIDE TO REAR PUSH SLIDE STOP UP 1C. INSPECT CLEAR EMPTY 1. Visually & physically check 2. Verify empty mag well
Step 1 Safety Check: Eject the magazine, lock the slide open with the slide stop lever, and visually and physically verify an empty chamber and magazine well.

Part 2: Field Stripping the Glock 19 Gen 5 / G19 MOS

Gliding the slide off a Glock requires releasing striker tension first and pulling the takedown lock tabs downward:

  1. Release Striker Tension: With the pistol confirmed empty and pointed in a safe direction, release the slide forward, press the trigger, and hold the trigger to the rear.
  2. Pull Slide Back Slightly & Lower Takedown Lock: Pull the slide back roughly 1/8 inch (3mm) while holding the trigger back, and pull the takedown lock tabs on both sides of the frame downward.
  3. Slide the Upper Forward Off the Frame: Release the trigger, then guide the slide assembly smoothly forward off the front of the frame rails.
  4. Remove the Recoil Spring Assembly & Barrel: Turn the slide upside down, compress/lift the dual recoil spring assembly slightly to clear the barrel lug and lift it out, then lift the rear of the 4.02" barrel upward and slide it out.
2A. PULL TAKEDOWN LOCK DOWN Hold trigger back, draw slide 1/8" & pull lock down 2B. SLIDE UPPER FORWARD OFF FRAME Guide slide forward off frame rails
Step 2 Takedown: After confirming empty, release striker tension, pull the slide back slightly while holding the takedown lock down, and ease the slide forward off the frame.
FIELD-STRIPPED GLOCK 19 GEN 5 / G19 MOS (4 MAJOR GROUPS) 1. Gen 5 / MOS Slide Keep striker channel dry 2. 4.02" GMB Barrel Bore, chamber & feed ramp 3. Dual Recoil Spring Gen 5 captive spring unit 4. Gen 5 Frame 4 rail pads + trigger housing
Four Field-Stripped Groups: Your Glock 19 Gen 5 / G19 MOS separates into the Slide Assembly, 4.02" Barrel, Gen 5 Recoil Spring Assembly, and Polymer Frame.

Part 3: Cleaning & Lubrication

Clean powder fouling from each part, wipe dry, and apply light lubrication only to designated contact points:

GLOCK 19 GEN 5 LUBRICATION MAP (LIGHT OIL — KEEP STRIKER DRY) 4.02" BARREL & SLIDE POINTS Thin oil film on barrel hood, lugs & exterior Keep bore, breech face & striker channel DRY FRAME RAILS & CONNECTOR Light oil on the 4 frame rail pads + light touch at connector & trigger bar
Step 4 Lubrication Map: Apply a thin sheen of oil to the barrel hood and exterior plus light oil on the 4 frame rail pads and connector contact while keeping the striker and bore dry.

Part 4: Reassembly & Function Check

  1. Reinstall the 4.02" Barrel & Recoil Assembly: Drop the barrel into the inverted slide, then seat the recoil spring assembly into the front slide hole and compress it onto the half-moon/lug seat on the barrel.
  2. Fit the Slide onto the Frame: Align the slide rails with the frame rails and pull the slide fully rearward so the takedown lock snaps upward into its locked position.
  3. Perform a Dry Function Check (Confirm Unloaded First): Rack the slide 2–3 times to verify smooth cycling, check trigger press and tactile reset, and confirm the slide locks open on an empty magazine.
5A. SEAT BARREL & SPRING 1. Drop barrel into slide 2. Seat recoil spring firmly against barrel lug seat 5B. INSTALL SLIDE ON FRAME Rack slide back until takedown lock snaps UP into place 5C. DRY FUNCTION CHECK 1. Rack slide 2–3 times 2. Verify trigger break & reset 3. Test empty-mag slide lock
Step 5 Reassembly & Verification: Seat the barrel and recoil spring, slide the upper onto the frame rails so the takedown lock snaps up, and complete a dry function check.

Best Maintenance Habits

  • Confirm an empty chamber and magazine well before every step
  • Keep the striker channel, breech face, and bore dry after cleaning
  • Use light oil on the 4 frame rail pads and connector contact
  • Complete a dry trigger, reset, and empty-magazine slide-lock check

Common Mistakes to Avoid

  • Spraying cleaner or oil directly into the striker channel
  • Over-oiling frame rails or MOS/optic threads
  • Seating the recoil spring improperly against the barrel lug
  • Skipping the post-reassembly dry function check

Video Walkthrough: Glock 19 Gen 5 Field Strip & Reassembly

Watch a step-by-step Glock 19 Gen 5 field strip, reassembly, and function check walkthrough.